Recessed Alarm Contacts

Alarm Contacts

Mini Type Magnetic Switch

DK6790

$5.75

White	Black

Window contact

Operating gap 2.3 cm max.
Size: 33.7 x 13.4 x 6.9mm

Recessed Alarm Contact

RAC1

$5.75

Alarm contact

Recessed magnetic reed switch
Mounting hole 9.5mm diameter
Contacts normally open

MCS-3102

$4.99

MAGNETIC SWITCH

Magnetic reed switch for security alarms.
normally closed contacts. (Closed Loop)
Screw terminals with cover.

Dim: 65 x 19.2 x 5 mm

100 V 500ma

47-600-0

$5.28

MAGNETIC SWITCH

Magnetic reed switch for security alarms.
Has normally open and normally closed switch contacts.
Screw terminals. 12VDC@500ma

PIR MOTION DETECTOR

GW-2712

$ 18.00

GW-2712 ¡V GENERAL PURPOSE PIR MOTION DETECTOR

GW-2712 is a general purpose PIR motion detector. It is designed to give a cost effective and reliable solution for residential and commercial security systems.

GW-2712 employs low noise dual-element pyro-electric sensor for motion detection and an MCU device in security logic and environment controls.

The alternate polarity signal processor inside the MCU has very high rejection to the common mode noise due to radio interference or power surges. The MCU device also provides the function of digital pulse counting, power-up delay and alarm output timing and controls. All of which maximizes security and false alarm immunity.

FEATURES

Low Noise Dual Element Pyro-Sensor
Alternate Polarity Signal Processing
Security Logics Are Integrated in The MCU Device
Surface-Mounted Component Technology, Greater EMI and RFI Immunity
Normal or Pulse Count Response for Harsh Environments
Supplied with Swivel Mounting Bracket for Angle Adjustment

SPECIFICATIONS

Operating Voltage : 8-16VDC
Current Drain : 15mA at 12VDC
Power-up Delay : 2 Minutes Typical with Flashing LED indication
Alarm Output : N.C. or N.O. Contact, 28VDC/100mA Rating
Alarm Period : 2-3 Seconds for Each Detection Output
Power Up Delay : 2 Minutes with Flashing LED
Pulse Count : 1 or 2 Alternate Polarity Pulses in 10 Seconds
Detection Pattern : 12 X 12 Metre, 90 Deg Maximum
Tamper Switch : N.C. Contact with 10 Ohm in Line Resistor. 12VDC/50mA Rating
Operating Temperature : 0 Deg C to 55 Deg C
Dimensions: 105(H) X 60(W) X 42(D) mm

Surface or Flush Mount

GW-9520

$ 25.00

GW-9520 ¡V SINGLE RELAY OUTPUT DIGITAL ACCESS CONTROL KEYPAD

GW-9520 is the simplified version of the GW-9521, mainly designed for stand-alone electric door lock installation. Its 5 Amp output relay provides N.C. and N.O. dry contacts for door strike and virtually compatible with any electric locking devices. Except the inter-lock and door monitoring facilities, the keypad has most of the basic features just like the other keypads in this series. A slim-line surface mount box in Beige color is supplied with each keypad. The box in Black color is also available on request when place order.

The GW-9520 is available in Back-lit keyboard or in Standard keyboard. The order number for Back-lit version is GW-9520BL, for Standard version is GW-9520.

FEATURES

* Direct 12-24V AC/DC Operation
* Over 100 Million Code Combinations
* 100 User Codes with 4-8 Digits
* Operates Fail-safe or Fail-secure Locking Device
* Door Lock Inhibit Authorization
* One 5 Amp Relay Output with N.C. & N.O. Contacts
* Auto or Manual Code Entry
* Output Activation Announcer
* Pacifier Tone Inhibit Control
* Egress Input for Door Remote Triggering
* All Features are Keyboard Programmable
* Non-volatile Memory in Power Failure
* Flush or Surface Mount
* Surface Mount Box in Beige (Standard Version) or Black (Back-lit Version)
* Size : 116(H) X 72(W) X 43(D) mm

Surface Mount

GW-2850

$ 89.00

GW-2850 ¡V METAL BACK-LIT KEYS, VANDAL RESISTANT, WEATHERPROOF, DUAL RELAY DIGITAL ACCESS CONTROL KEYPAD

GW-2850 is a full feature keypad system. It consists of 2 relay outputs controlled by 2 groups of independent User Codes. Output 1 is a 5 Amp rating relay providing both N.C. and N.O. dry contacts for door strike, Output 2 is a 1 Amp rating relay also providing N.C. and N.O. dry contacts for other control applications, such as controlling of an alarm system. Three on board LED lamps are wired internally to indicate the operation status of the outputs 1 and 2 and the system status. The keypad utilizes terminal block for all the external connections.

MAIN FEATURES ¡V GW-2850

Back-lit Metal Button Keypad
1.5mm Stainless Steel Face Plate
Vandal Resistant & Weatherproof
Die Cast Metal Housing
Direct 12-24V AC/DC Operation
Dual Relay Output
100 User PIN for Output 1
10 User PIN for Output 2
Surface Mount or Post Mounting
Fits Single Gang Flush Mount Box
Dimensions: 125(H) X 79(W) X 46/54(D: bottom side/upper side) mm

CS 8-ZONE DIALER ALARM KIT

GW-268

$99.90

GW-268 ¡V 8-ZONE ALARM CONTROL PANEL WITH AUTO-DIALER

GW-268 is an auto-dialer alarm control panel with 8 hardware protection zones and 2 software zones for panic and duress alarms, which is designed for home and office protections. The system gives local alarm warnings as like the traditional alarm systems as well as sending voice message to 4 telephones of pre-set numbers when alarm occurs. The auto dialer is compatible with all the public telephone systems. The control panel comes with one control console for ready installation. Each GW-268 comes with one alarm control panel and one full feature master control console. Auxiliary control consoles can be purchased separately. Both types of consoles are back lighting and have the same function except the built-in microphone for message recording is not available on the auxiliary control console.

FEATURES FOR ALARM

8 Zones, Programmable for Instant, Delay (2 delay time available), 24 Hour Instant or 24 Hour Silent Alarm Reporting
Programmable Master Code and 8 User Codes
All User Codes with Duress Function
Protection Zones are Programmable for Single or Multiple Triggering
Programmable Time for Exit, Entry (2 timings) and Alarm Duration
Arm-Disarm Control from Keypad or Remotely from Any DTMF Telephone mobile Phone
Each Protection Zone is Programmable for Response Time
Exit and Entry Warning Beeps On-Off Options
Arm-Disarm Ring Back Indication On-Off Options
Instant Arming Codes for Home and Away Operations
Built-in Dynamic Battery Charger and Tester with Auto or Manual Testing Options
Two On Board Software Zone for Panic and Duress Alarms
Maximum 4 Control Keypads Can Be Connected
Home or Away Operation
Forced to Arm or Arm Prohibited Options
Handover Option for The Instant Zones
Facilities for Driving Siren/Bell, Satellite Siren and Strobe Light
Power Low Watchdog Resets System
Non-Volatile Memory
Can be Arm-Disarmed by Conventional Key Switch
Full Feature Default Values in System for Ready Use
12V / 6.5Ah Back-up Battery (Not Included)
16.5VAC Operation
Weight: 2.2 Kg (The Control Panel); 220 g (The Keypad)
Dimensions: 268(H) X 263(W) X 78(D) mm (The Control Panel); 117(H) X 117(W) X 27(D) mm (The Keypad)

FEATURES FOR AUTO-DIALER

Four 32 Digit Telephone Numbers for Auto-Dialer
Two 32 Digit Telephone Numbers for Communicator
Communicator Data in DTMF Format with Check-sum
Tone or Pulse Dialing
Programmable Pause Time between Any Digits
Voice Message and Numeric Message are Possible
20 Seconds Non-Volatile User Programmable Voice Message
Controllable Listen-in Duration
Back-up or Non-back-up Dialing for Alarm Reporting
Automatic Telephone Line Fault Detection
Programmable Dialing Attempts, 8 Maximum
Programmable Message Repeats, 8 Maximum
Telephone Numbers can be Tested Individually