NTE Type Number |
Description and Application |
Case Style |
Drain to Source Breakdown Voltage (Volts) |
Gate to Source Cutoff Voltage (Volts) |
Gate to Source Breakdown Voltage (Volts) |
Maximum Continuous Drain Current (Amps) |
Static Drain to on Source Resistance (Ohms) |
Input Capacitance (pf) |
Forward Transcon- ductance (mhos) |
Device Total Power Dissipation @TC=25°C (Watts) |
BVDSS | Vgs(Off) | BVGSS | ID | rDS(On) | Ciss | gfs | PD | |||
2980 $3.84 |
N-CHANNEL Enhancement Mode High Speed Switch |
TO126N | 60 Min | 2.0 Max | ±10 Max | 7.7 | 0.20 Max | 400 Typ | 3.4 Min | 25 Max |
td(off) = 17ns, td(on) = 9.3ns,tf = 26ns, tr = 110ns | ||||||||||
2981 $3.54 |
N-CHANNEL Enhancement Mode High Speed Switch |
TO126N | 100 Min | 2.0 Max | ±10 Max | 7.7 | 0.27 Max | 490 Typ | 4.4 Min | 42 Max |
td(off) = 21ns, td(on) = 9.8ns,tf = 27ns, tr = 64ns | ||||||||||
2984 $2.74 |
N-CHANNEL Enhancement Mode High Speed Switch |
TO220 | 60 Min | 2.0 Max | ±10 Max | 17 | 0.10 Max | 8700 Typ | 7.33 Min | 60 Max |
td(off) = 23ns, td(on) = 11ns,tf = 41ns, tr = 110ns | ||||||||||
2985 $4.10 |
N-CHANNEL Enhancement Mode High Speed Switch |
TO220 | 60 Min | 2.0 Max | ±10 Max | 30 | 0.05 Max | 1600 Typ | 12 Min | 88 Max |
td(off) = 30ns, td(on) = 14ns,tf = 56ns, tr = 170ns | ||||||||||
2986 $7.38 |
N-CHANNEL Enhancement Mode High Speed Switch |
TO220 | 60 Min | 2.0 Max | ±10 Max | 50 | 0.028 Max | 3300 Typ | 23 Min | 150 Max |
td(off) = 42ns, td(on) = 17ns,tf = 110ns, tr = 230ns | ||||||||||
2987 $4.56 |
N-CHANNEL Enhancement Mode High Speed Switch |
TO220 | 100 Min | 2.5 Max | ±15 Max | 20 | 0.12 Max | 1200 Typ | 10 Min | 105 Max |
td(off) = 80ns, td(on) = 50ns,tf = 80ns, tr = 140ns |
DESCRIPTION
The NTE series Logic Level MOSFETs are compatible with the
5-volt power-supply requirement of logic circuitry. These devices do not require
an interface circuit between it and the CMOS logic driver; therefore, the extra
cost of the interface circuit power supply is eliminated.
The chief physical structural difference between Logic Level and other MOSFETs, and the electrical reason for its difference in performance, is its gate insulation thickness, which has been reduced from 100nm industry standard to 50nm (500 angstroms), yet which retains the dynamic strength to handle the high voltage applied to power transistors. Since the surface inversion of the MOS channel is determined by the gate-insulator voltage field, the halving of the gate-oxide thickness should be expected to have a major effect on the gate voltage required. In fact, this reduction is the reason for voltage reduction from 10 volts (standard MOSFETs) to 5 volts (Logic Level MOSFETs).
Tight control of the temperature vs. time and oxygen vs. time profiles applied to the silicon substrate during oxide growth assures consistant preformance through the development of good transition regions between the oxide, the silicon below it, and thew polysilicon above it. The reduction in gate insulator thickness makes possible easy ON/OFF control of the Logic Level MOSFETs by CMOS logic alone, and by microprocessors.
Although it might be expected that halving the gate-oxide thickness would double the gate capacitance and halve the switching speed, measurements demonstrate a 2:1 increase in switching speed over the 10 volt MOSFET when gate drive power is the same for both devices. For example, the rise time of a 10 volt MOSFET is typically 120ns, that of a Logic Level MOSFET, 60ns, even though drain-to-gate feedback capacitance is higher than in the 10 volt type.
For more info on parts go to NTE website